PS1 Powerstand Connections / Line Out: Difference between revisions
mNo edit summary |
mNo edit summary |
||
| (13 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
<big>'''PS1 Connections Lines Out '''</big> | <noinclude><big>'''PS1 Connections Lines Out '''</big> </noinclude> | ||
== Summary == | {{Classic icon}}{{Model I icon}} | ||
=== Line | <noinclude>== Summary == | ||
</noinclude><section begin=Connections /> | |||
<includeonly>==PS1 Connections Lines Out==</includeonly> | |||
=== Line Out (XLR balanced) for Channels 1 and 2 === | |||
* post trim (+4 dBu nominal) | * post trim (+4 dBu nominal) | ||
| Line 9: | Line 12: | ||
=== SPDIF Data OUT === | === SPDIF Data OUT === | ||
* | * Post trim | ||
* | ** Input Trim | ||
* | ** R1 Remote Channel volume | ||
* | **Insert returns | ||
* Pre | |||
** Preset | |||
** Tone controls | |||
** R1 Remote Master volume. | |||
* SPDIF is channels 1 & 2 only. | * SPDIF is channels 1 & 2 only. | ||
The Data OUT is a SPDIF output with a sampling rate of 48KHz | The Data OUT is a SPDIF output with a sampling rate of 48KHz. | ||
Set your recording software as below if given the options | |||
* 24 Bit | |||
* 48 KHz | |||
* S/PDIF (RCA) | |||
See: [http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/1431057611?r=1771034582#1771034582 Recording Through the PS1] — Message Board Discussion. | |||
<section end=Connections /> | |||
{{:PS1 Powerstand Connections/Line Out/XLR}} | {{:PS1 Powerstand Connections/Line Out/XLR}} | ||
{{:PS1 Powerstand Connections/Line Out/Insert}} | {{:PS1 Powerstand Connections/Line Out/Insert}} | ||
| Line 25: | Line 39: | ||
[[ | [[Category:L1® System]] | ||
[[category:PS1 Powerstand]] | [[category:PS1 Powerstand]] | ||
[[category:PS1 Powerstand Connections]] | [[category:PS1 Powerstand Connections]] | ||
Latest revision as of 14:39, 5 November 2010
PS1 Connections Lines Out
Summary
Line Out (XLR balanced) for Channels 1 and 2
- post trim (+4 dBu nominal)
Insert Send
- post trim,
- post channel volume
SPDIF Data OUT
- Post trim
- Input Trim
- R1 Remote Channel volume
- Insert returns
- Pre
- Preset
- Tone controls
- R1 Remote Master volume.
- SPDIF is channels 1 & 2 only.
The Data OUT is a SPDIF output with a sampling rate of 48KHz.
Set your recording software as below if given the options
- 24 Bit
- 48 KHz
- S/PDIF (RCA)
See: Recording Through the PS1 — Message Board Discussion.
Line Outs (XLR balanced) for Channels 1 and 2
- post trim (+4 dBu nominal)
For Channels One or Two you can run an XLR cable to the House or recording console like this. The outputs are post-trim (+4 dBu nominal).
This is not suitable for connection to another PS1 Power Stand (Classic) / Model I as the output level is too high for a PS1 Power Stand (Classic) / Model I Channel 1 or 2 input. If you want to connect one L1® to another please see: PS1 Powerstand / Daisy Chain
Line Out from Insert Point
- access from the "ring" connection at the Insert Point
- post trim
- post R1 Remote Channel Level
For Channels One or Two insert a 1/4 inch cable halfway into the Insert jack to get a signal that is controlled by the volume control on the Remote. This is also known as the Half Insert method. For more information about 1/4 cables see Tip Ring Sleeve connections. The rectangular box shown below the input panel is a DI, used to output the signal to a console or house system.
Line Out from Channels 3 or 4
There is no output from the PS1 Power Stand (Classic) / Model I for Channels 3 or 4. To share inputs with an external system use a DI.
