Mixer / Yamaha / MG124 CX: Difference between revisions
Jump to navigation
Jump to search
| (11 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
<table><tr> | |||
<td valign="top" width="250">__TOC__</td> | |||
<td valign="top">To use a Yamaha MG124 CX Mixer with the {{Model II}} | |||
</td> | |||
</tr></table> | |||
==== Overview ==== | |||
On the mixer | |||
* Pan all the inputs hard LEFT | |||
* Run a line out of the LEFT output to the Model II Power Stand Analog input (cable details below) | |||
[[Image:YamahaMG124 to Model II Power Stand Analog Input.png]] | |||
[[Image: | ==== Settings on the L1® Input Panel ==== | ||
Start off with the Input Trim at '''3''' and adjust if necessary so that the Signal/Clip light stays green most of the time. Occasional flickers of yellow are okay. If it is flickering or solid red, turn down the Input Trim. | |||
[[Image:ModelIIInputsForTwoLT1.png]] | |||
==== Cable Details ==== | |||
==== ¼ inch jack inch to ¼ inch ==== | |||
<table><tr><td valign="top"> | |||
This mixer has ¼ inch jack balanced outputs. Any of the cables shown below should work. | |||
===== ¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Ring-Sleeve (balanced) ===== | |||
The output of this mixer is balanced, and the input on the Model II Power Stand is also balanced, so this is the preferred method. | |||
[[Image:trsMtrsM.png|Tip-Ring-Sleeve to Tip-Ring-Sleeve]] | |||
===== ¼ Inch Tip-Sleeve (unbalanced) to ¼ Inch Tip-Sleeve (unbalanced) ===== | |||
[[Image:TsMtsM.png|Tip-Sleeve to Tip-Sleeve]] | |||
===== ¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Sleeve (unbalanced) ===== | |||
[[Image:trsMtsM.png|Tip-Ring-Sleeve to Tip-Sleeve]] | |||
</td></tr></table> | |||
=== Documents === | |||
* {{Model II}} | |||
* [http://download.yamaha.com/api/asset/file?language=en&site=countrysite-master.prod.exp.yamaha.com&asset_id=8043 Yamaha MG124CX/MC124 Owner's Manual] | |||
[[Image:YamahaMG124 Output.png]] | |||
---- | |||
[[Category:Mixer]] | |||
[[Category:Yamaha]] | |||
Latest revision as of 13:02, 19 September 2012
| To use a Yamaha MG124 CX Mixer with the L1 Model II |
Overview
On the mixer
- Pan all the inputs hard LEFT
- Run a line out of the LEFT output to the Model II Power Stand Analog input (cable details below)
Settings on the L1® Input Panel
Start off with the Input Trim at 3 and adjust if necessary so that the Signal/Clip light stays green most of the time. Occasional flickers of yellow are okay. If it is flickering or solid red, turn down the Input Trim.
Cable Details
¼ inch jack inch to ¼ inch
|
This mixer has ¼ inch jack balanced outputs. Any of the cables shown below should work.
¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Ring-Sleeve (balanced)The output of this mixer is balanced, and the input on the Model II Power Stand is also balanced, so this is the preferred method.
¼ Inch Tip-Sleeve (unbalanced) to ¼ Inch Tip-Sleeve (unbalanced)
¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Sleeve (unbalanced)
|
Documents
