Difference between revisions of "Template:L1 Pro"

ToneMatch Presets
Tone Controls
Reverb
The signal from a ToneMatch mixer connected to the ToneMatch port including ToneMatch Presets, zEQ, Reverb, Effects.

The sound is NOT affected by the L1 Pro System EQ setting.

L1 Pro ToneMatch Switch

The ToneMatch switch selects the ToneMatch Preset applied to the input.

It does not adjust the channel’s gain staging or level. It does not function like a MIC/LINE switch found on some powered loudspeakers or mixers

ToneMatch Preset Behavior:

MIC applies the microphone ToneMatch Preset
INST applies the acoustic guitar ToneMatch Preset
OFF disables ToneMatch processing

Use MIC for microphones and INST for acoustic guitar. You can change the ToneMatch Presets using the Bose App

Channel ToneMatch Button: Select the ToneMatch preset for an individual channel. The corresponding LED will illuminate white while selected.

More information about ToneMatch Presets

L1 Pro Daisy Chain

Want to connect one or more L1 Pro systems together? See L1 Pro Daisy Chain

L1 Pro System EQ

The System EQ feature on the L1 Pro systems applies an EQ preset to the master output. This is similar to a graphic equalizer on traditional analogue mixers, but it uses four presets instead for quick access. read more — L1 Pro System EQ

L1 Pro32 Half Stack

Can I operate the L1 Pro32 with only the lower section of the line array?: Sometimes there is not sufficient height to use the full array

Yes: The L1 Pro32 can be used without the upper array. This configuration is useful when a venue ceiling cannot accommodate the height of the L1 Pro32
Source: Page 7 of the L1 Pro32 Owners Guide

For best results, ensure array is at ear level for listeners
Unlike the L1 Model II, the L1 Pro32 automatically adjusts the level of the bass output to maintain the appropriate spectral balance.

It’s a valid use case to use only the bottom array section. In fact, the EQ automatically adjusts to compensate.
Craig Small - Bose

Half Stack Not Recommended for Small Gigs

Running only the lower section of the Line Array is a workaround when there isn't enough ceiling clearance to use both sections. For small gigs, turn down the volume on the L1 Pro32, don't run without the top section of the array because

You'll need to elevate the system so the array is at ear level for the audience. Otherwise, the sound will be muffled
You will reduce your projection over distance. The sound will drop off more over distance.
You may need to turn up the volume louder than if you were using the full array. As a result, you increase the likelihood of feedback.

L1 Pro Emergency Kit

L1 Pro

S1 Pro+

These are extras and spares I carry in addition to the items I know I will need at a gig.

**Emergency and Spares Kit for L1 Pro and S1 Pro(+)**
Item	Reason
IEC Power Cord	They got lost, and this can be used with an XLR cable to substitute for a SubMatch Cable
XLR cable	It's always good to have a spare. Use with an IEC Power Cord to replace a SubMatch Cable
1/4-inch (6.3mm) Tip-Ring-Sleeve Cable	Connect mixers or devices with balanced connections to the L1 Pro.
1/4-inch (6.3mm) Tip-Sleeve Cable	This is your basic instrument cable. It's always good to have a spare.
XLR Female to 1/4-inch (6.3mm) Tip-Ring-Sleeve Cable	To connect Line Level Output from an L1 Pro or third-party mixer to Channel 3 input of an L1 Pro or S1 Pro+
1/8-inch (3.5 mm) Tip-Ring-Sleeve Cable	Use this to connect the headphone output of a consumer device to L1 Pro or S1 Pro(+) channel 3 input
CAT5 cable	Connect ToneMatch Mixers (T1/T4S/T8S) to the L1 Pro ToneMatch Port
ToneMatch Power Supply	In case I need to run two ToneMatch Mixers to a single L1 Pro
Dynamic Microphone	This is a spare; the one to use when you have guest speakers making announcements
Microphone Clip	They break
Multi-bit Screwdriver	Tighten, loosen, everything as needed
Gaffers Tape	Tie down cables, or quick repairs
Labels with contact information	I have labels on all my gear, but it's good to have spares in case they fall off

FAQ

General Questions

 Expand all | Collapse all

Are the columns made of plastic?

Arrays on all units feature an extruded aluminum sleeve. Perforated grille on the front, solid on the back. Source: Craig Small

Can I swap the columns from different models?

No. While the column arrays and extensions of the L1 Pro8 and L1 Pro16 will fit each other, no sound comes out.

L1 Pro32, can I take off the top column?

Yes

The L1 Pro32 can be used without the upper array. This configuration is useful when a venue ceiling cannot accommodate the height of the L1 Pro32
Source: Page 7 of the L1 Pro32 Owners Guide

For best results, ensure the array is at ear level for listeners

The L1 Pro32 automatically adjusts the level of the bass output to maintain the appropriate spectral balance.

It’s a valid use case to use only the bottom array section. In fact, the EQ automatically adjusts to compensate.
Craig Small - Bose

Half Stack Not Recommended for Small Gigs

Running only the lower section of the Line Array is a workaround when there isn't enough ceiling clearance to use both sections. For small gigs, turn down the volume on the L1 Pro32, don't run without the top section of the array because

You'll need to elevate the system so the array is at ear level for the audience. Otherwise, the sound will be muffled

You will reduce your projection over distance. The sound will drop off more over distance.

You may need to turn up the volume louder than if you were using the full array. As a result, you increase the likelihood of feedback.

Inputs and Connections

 Expand all | Collapse all

Is MIC/INST/OFF the same as a MIC/LINE switch?

No. The MIC/INST/OFF switch is NOT a MIC/LINE selector like those found on many powered loudspeakers.
The switch does not change input sensitivity or gain.
It affects only the ToneMatch Preset applied to the input.
ToneMatch Preset Behavior:

MIC applies the microphone ToneMatch Preset

INST applies the acoustic guitar ToneMatch Preset

OFF disables ToneMatch processing

Use MIC for microphones and INST for acoustic guitar. You can change the ToneMatch Presets using the Bose App
Channel ToneMatch Button: Select the ToneMatch preset for an individual channel. The corresponding LED will illuminate white while selected.
More information about ToneMatch Presets

Does the MIC/INST/OFF switch change the input gain?

No. The MIC/INST/OFF switch does not change input sensitivity or gain.
It only selects the ToneMatch Preset applied to the input.
It does not adjust the channel’s gain staging or level.
ToneMatch Preset Behavior:

MIC applies the microphone ToneMatch Preset

INST applies the acoustic guitar ToneMatch Preset

OFF disables ToneMatch processing

Use MIC for microphones and INST for acoustic guitar. You can change the ToneMatch Presets using the Bose App
Channel ToneMatch Button: Select the ToneMatch preset for an individual channel. The corresponding LED will illuminate white while selected.
More information about ToneMatch Presets

How do I connect a monitor?

* You can connect the L1 Pro Line Out to a monitor.
The XLR Line Output from any L1 Pro contains the sound from all inputs (1, 2, 3, Bluetooth, and ToneMatch Port). That includes

ToneMatch Presets

Tone Controls

Reverb

The signal from a ToneMatch mixer connected to the ToneMatch port including ToneMatch Presets, zEQ, Reverb, Effects.

The sound is NOT affected by the L1 Pro System EQ setting.

If you have an S1 Pro, see L1 Pro to S1 Pro

If you have an S1 Pro+, see L1 Pro to S1 Pro+

If you prefer to run your inputs to the S1 Pro+ and send the output to the L1 Pro, see S1 Pro+ To L1 Pro

If you have a mixer, you may prefer to send the monitor mix from the mixer to the monitors instead of the L1 Pro Line Out

The L1 Pro was designed to be placed behind the performers. If you can do that, you may not need a monitor — you should be able to hear yourself clearly. For more about that, see The L1® Approach and the History Of Amplification.

How do I connect a third‑party mixer to the L1 Pro?

Use the Mixer Mono Output and connect it to L1 Pro Channel 3.
If the mixer does not have a mono output, pan all inputs hard LEFT and use the LEFT output. We will now refer to that as the Mixer Mono Out.
If the mixer has XLR outputs:

Mixer Mono Out → XLR Female → ¼″ (6.3 mm) Tip‑Ring‑Sleeve → L1 Pro Channel 3

If the mixer has ¼″ (6.3 mm) Tip‑Ring‑Sleeve outputs:

Mixer Mono Out → ¼″ (6.3 mm) Tip‑Ring‑Sleeve → L1 Pro Channel 3

For more details, see Mixer to L1 Pro.

Can I use XLR cables from my mixer into Channels 1 or 2?

You can, and it might work. Click for details

And yes, there are even pictures of this in the L1 Pro manuals.
However, using XLR‑to‑XLR connections from a mixer into Channels 1 or 2 can lead to problems.

1. Some mixers have a MIC/LINE or ‑20 dB switch on the XLR output

If your mixer can switch its XLR output to MIC or ‑20 dB, then engage that switch and the XLR‑to‑XLR connection should work.
If not, use Mixer Mono Out → XLR Female → ¼″ (6.3 mm) Tip‑Ring‑Sleeve → L1 Pro Channel 3.

2. Most mixer XLR outputs are line‑level, which is a poor match for the L1 Pro’s mic‑level XLR inputs

This mismatch can cause:

Input clipping

Harsh distortion

Unpredictable behavior

3. You can sometimes “make it work,” but it’s not ideal

You might avoid clipping by:

Turning down the mixer output

Turning down the L1 Pro channel volume

However:

Lower mixer output reduces signal‑to‑noise ratio (more hiss)

Very low L1 Pro channel settings give almost no usable range

Volume may jump from too quiet → too loud with tiny adjustments

4. Channel 3 avoids all of these issues

Channel 3 is designed for line‑level sources and provides:

Proper level matching
Lower input sensitivity (less likely to clip/distort)

Full +24 dBu headroom

Predictable behavior
No ToneMatch presets

No Reverb

No DSP gain steps

This is why the recommended method is:

Mixer Mono Out → XLR Female → ¼″ (6.3 mm) Tip‑Ring‑Sleeve → L1 Pro Channel 3

Why are the ¼″ (6.3 mm) Tip‑Ring‑Sleeve inputs on Channels 1 and 2 louder than the ¼″ (6.3 mm) Tip‑Ring‑Sleeve input on Channel 3?

By design, the input sensitivity of the Channel 3 ¼″ (6.3 mm) Tip‑Ring‑Sleeve input is lower than the ¼″ (6.3 mm) Tip‑Ring‑Sleeve inputs on Channels 1 and 2. This allows Channel 3 to handle line‑level sources with less risk of clipping.
You can achieve the same overall output level from Channel 3, but you may need to turn the Channel 3 volume control higher to do it.
This difference is most noticeable when connecting a third‑party mixer to the L1 Pro.
People tend to hear louder as better, so you may prefer to use Channels 1 and 2 instead of 3, but you can get the same result by turning up the volume on Channel 3, leaving the other channels available.
For more information, see Mixer to L1 Pro.

Multiple L1 Pro Systems

 Expand all | Collapse all

What can and can’t multiple L1 Pros do together?

Multiple L1 Pros can be used together, but each system still operates independently.

What they can do

Pass audio from one unit to another using the L1 Pro Line Out (Daisy Chain)

With a mixer

Play the same signal if you feed each unit from a mixer

Work as a stereo pair when fed LEFT and RIGHT outputs from a mixer

What they can’t do

Share their internal inputs with each other

Combine all inputs from two units into one system

Link wirelessly over Bluetooth (Bluetooth is receive‑only)

For details on specific setups, see the related questions below.

How do I connect one L1 Pro to another L1 Pro (daisy chain)?

Use XLR Female → ¼″ (6.3 mm) Tip‑Ring‑Sleeve to connect

From the first L1 Pro Line Out

To the second L1 Pro Channel 3 ¼″ (6.3 mm) Tip‑Ring‑Sleeve input.

For complete details, see L1 Pro Daisy Chain.

Can I use Bluetooth to connect two L1 Pros?

No.
L1 Pro systems can receive Bluetooth audio from a Bluetooth source (for example, a phone, tablet, or computer). They cannot send Bluetooth to another L1 Pro, and even if they could, the latency (delay) would make this unusable in a live sound setting.
For more information see L1 Pro Daisy Chain

Can I run two L1 Pros as a single mono system?

No, you need a mixer to do this.
An L1 Pro cannot link its inputs or internal mix to another L1 Pro. Each unit only plays the signals connected to its own inputs.
If you want both L1 Pros to play the same mono mix, use a mixer and send the same output to each unit:

From the mixer Mono Output → L1 Pro (Left) Channel 3 ¼″ (6.3 mm) Tip‑Ring‑Sleeve input

From the mixer Mono Output → L1 Pro (Right) Channel 3 ¼″ (6.3 mm) Tip‑Ring‑Sleeve input

This gives you two identical mono feeds, but the L1 Pros still operate as separate systems.
For more details, see Dual Mono.

How do I connect two L1 Pros for stereo?

To run two L1 Pros in stereo, send the LEFT and RIGHT outputs from your mixer to each L1 Pro separately.

From the mixer LEFT Output → L1 Pro (Left) Channel 3 ¼″ (6.3 mm) Tip‑Ring‑Sleeve input

From the mixer RIGHT Output → L1 Pro (Right) Channel 3 ¼″ (6.3 mm) Tip‑Ring‑Sleeve input

Each L1 Pro then reproduces its own channel (Left or Right), creating a stereo pair.
For more details, see Mixer to L1 Pro.

Can I connect my L1 Pros so they share inputs?

You can't.

You cannot take the three inputs on each L1 Pro and hear all six inputs through both units.

While you can daisy chain the inputs of the first L1 Pro to a second L1 Pro, you cannot send the inputs of the second L1 Pro back to the first. Doing so will create a feedback loop.

For more details, see L1 Pro Daisy Chain.

Can I run two L1 Pros in mono without a mixer?

You can't.
There is no way to link two L1 Pros so they both play the same mono signal without using an external mixer.
Each L1 Pro only plays the signals connected to its own inputs.
If you need both L1 Pros to reproduce the same mono mix, you must use a mixer and send the same output to each unit.
For more details, see Mixer to L1 Pro.

Troubleshooting

 Expand all | Collapse all

The L1 Pro sounds muddy

Symptoms

No mid-highs, low volume, it's all bass

Possible Causes

L1 Pro speaker column or extension not seated properly.

Solutions

Make sure the column arrays are seated firmly in the power stand

Excessive Hiss

Hiss with nothing connected to the L1 Pro inputs when I turn up the volume

Symptoms

Hiss with nothing connected, volume turned up

Possible Causes

with no input, turning up the volume amplifies noise

Solutions

turn down the volume or mute any unused channels For more details see L1 Pro Hiss

Hiss when connecting the LINE OUT from an L1 Pro to a second L1 Pro with an XLR cable

Symptoms

Hiss, noise, clipping

Possible Causes

LINE OUT from the first L1 Pro is line-level.
XLR input on the second L1 Pro is microphone-level

Solutions

Connect the first L1 Pro LINE OUT to the second L1 Pro Channel 3 input The cable: Female XLR to 1/4-inch (6.3mm) Tip-Ring-Sleeve cable For more details see L1 Pro Daisy Chain

Hiss when connecting a mixer to the L1 Pro Channels 1 or 2 with an XLR cable

Symptoms

Hiss, noise, clipping

Possible Causes

No causes provided

Solutions

Connect the mixer mono output to the L1 Pro Channel 3 input The cable: Female XLR to 1/4-inch (6.3mm) Tip-Ring-Sleeve cable For more details see Mixer to L1 Pro

Feedback Issues

 Expand all | Collapse all

What causes microphone feedback?

Feedback happens when the sound from the loudspeaker is louder at the microphone than the sound of the voice. If the microphone “hears” more speaker than performer, the system will feed back.
For a full explanation and diagrams, see Feedback / Microphone.

How do I set gain staging to reduce feedback?

Set your source at its loudest performance level, then raise the Trim until you get solid green with occasional yellow (never red). Once Trim is set, use channel volume for mixing — not Trim.

Details for the T4S/T8S

The first thing you do when connecting a sound source to your ToneMatch mixer is set the input trim. This is gain staging. Then you can set the ToneMatch Preset for your source. We'll do both in the short video below.

At the beginning of the video, I'm doing a factory reset so we don't bump into any old settings. You do not have to do a factory reset before you set the input trim on your ToneMatch mixer.

The trim controls across the top will be different

The trim controls across the top of your ToneMatch mixer will likely be different. This is because the output levels of your input sources will likely be different. This is normal.

Mixing - Use the volume controls not the trim controls

Once you have set the input trim, you should not have to change it until you change the input source (e.g. different microphone, singer, or instrument). Do not use the trim control to change the channel volume. Use the channel volume control.

Scenes

Saved Scenes do not capture the trim, channel volume, or Master Volume settings.

Set Up Your Source

Set your source at the maximum that it will be when performing.

Microphone

Sing directly into the microphone using close microphone technique (lips just brushing the windscreen). Sing as loudly as you will sing during your performance. You want to set the Trim to work at your maximum volume.

Instrument

Turn your input as high as it is likely to go during performance.

Trim Controls

The ToneMatch Mixer^[1] trim controls for Channels 1-4 (1-8 for the T8S ToneMatch mixer) provide a significant gain increase when you reach the upper limit. This increase in gain is normal operation.
Most sources like typical microphones and piezo pickup systems can provide enough level without the need to add significant gain from the trim control. Certain sources like passive acoustic guitar pickups require additional gain and in these cases it can be necessary to set the trim level to the upper range of the control. When the trim control is set this high you may notice the gain change. This is normal operation. If you want to run the trim control at lower settings we recommend using a preamp or simple stomp box level booster.

The trim for Aux input channels 5/6 (9/10 for the T8S ToneMatch mixer) do not exhibit the same behavior as the trim controls for Channels 1-4 (1-8 for the T8S ToneMatch mixer). The Aux inputs are designed for line level sources and do not have the same gain staging as channels 5/6 (9/10 for the T8S ToneMatch mixer).

Details for the T1

Here's a quick video to help you set the input trim for a microphone on the T1 ToneMatch Audio Engine. This is called Gain Staging.

The trim controls across the top will be different

The trim controls across the top of your T1 ToneMatch Audio Engine will likely be different. This is because the output levels of your input sources will likely be different. This is normal.

Mixing - Use the volume controls not the trim controls

Once you have set the input trim, you should not have to change it until you change the input source (e.g. different microphone, singer, or instrument). Do not use the trim control to change the channel volume. Use the channel volume control.

Scenes

Saved Scenes do not capture the trim, channel volume, or Master Volume settings.

The same principles apply to an instrument or line-level input.

Set the source to the highest level you will need during the show

Set the input trim so that you get solid green, occasional yellow flickers, and never see red.

For more detailed steps for T1, T4S, and T8S, see Feedback / Microphone#Gain Staging.

Microphone Technique?

Use close‑microphone technique: lips touching the windscreen. Every halving of distance gives roughly 6 dB more gain before feedback.

Close Microphone Technique details

Get close to the microphone when you want to be loud. No other technique has a big an impact on feedback. Each halving of distance is approximately another 6 dB of gain before feedback. This relationship in physics is known as the Inverse Square Law. This means that the difference between working a microphone at 2 inches, and 1/4 inch is 18 dB, which is more than twice as loud. While good mic technique often involves "working" the microphone at different distances, singers must be mindful of the fact that small changes in distance from the mouth result in very dramatic changes in sound level.
In the feedback diagram at the top, getting close to the microphone means getting more sound from voice which translates to more gain without feedback.

For more, see Feedback / Microphone#Close Microphone Technique.

Do directional microphones help with feedback?

Yes. Supercardioid and hypercardioid microphones provide the best gain‑before‑feedback, followed by cardioid. Omnidirectional microphones provide the least.

Details about Directional Microphones

Principles
Use a directional microphone. Hypercardioid is better than cardioid, which is better than omnidirectional. All sound waves impinging on the microphone from a direction other than the intended signal is "noise" and will lower the threshold of feedback.
Directional microphones "collect" less sound from directions other than what they're supposed to amplify (the voice, or an instrument) and hence are less likely to feed back.
In addition, most directional microphones have a strong behavior called proximity effect. This is the strong buildup of bass and low-mid response as the source (say the voice) to microphone distance decreases. For microphones intended to sound natural when the voice is very close -- say one of a number of popular stage vocal microphones -- what this means is that low-to-middle frequencies from sources at a distance, including loudspeakers being used to amplify the voice, are largely rejected by the microphone. This is a real plus in terms of avoiding microphone feedback.
Conversely, an omnidirectional microphone (equal sensitivity to sound coming from any direction) has no proximity effect. This is an advantage often in the studio where the engineer wants consistent tone regardless of distance. But it's a disadvantage on stage in terms of feedback. An omnidirectional mic collects more sound that's not the target, and because it has no proximity effect is more susceptible to feedback at low-to-mid frequencies than a directional mic.

Omnidirectional and Unidirectional Microphones

There are two basic types of microphone — omnidirectional and unidirectional^[2].

Omnidirectional Microphone

Omnidirectional mic. It is sensitive to sounds from all directions.
Best to use when more room ambiance is the goal. Direct and ambient sound can be adjusted by moving the mic closer to or further from the sound source.

Unidirectional Microphone

Unidirectional microphones are sensitive to sound coming from only one direction. Examples:

a vocalist singing directly on axis directly into the microphone

a guitar amplifier with the microphone aimed directly at the speaker cone

Cardioid

The most common type of unidirectional microphone is called a “cardioid” because its pickup pattern is heart-shaped. It picks up most sound from the front of the microphone and some from the sides.
Although you will get better gain-before-feedback from a cardioid microphone than an omnidirectional microphone, you will get better gain-before-feedback from a supercardioid or hypercardioid microphone (see next section).
Examples of common cardioid microphones (good to great microphones but not necessarily the best for gain-before-feedback with Bose L1 systems)

Sennheiser e 835, e 935, MD 935

Shure SM 58, SM 57, Beta 87C

Supercardioid / Hypercardioid

Supercardioid or hypercardioid microphones offer even greater sound isolation through narrower pickup patterns.

Examples of common supercardioid/hypercardioid microphones

Audix OM 5, OM 3b, OM 6, OM 7, VX 5

EV N/D 767A

Neumann KMS 105

Sennheiser e 845, e 865, e 945, e 965, MD 441, MD 945,

Shure Beta 58A, Beta 87A

For examples and diagrams, see Feedback / Microphone#Directional Microphones.

How should I place monitors to avoid feedback?

If you are using stage monitors, be sure to place them so they are directing sound at the area of the microphone that rejects the most sound.
Note from Shure.com

Other variants on the unidirectional polar pattern include supercardioid and hypercardioid options. Both patterns offer narrower front pickup angles than the cardioid – 115 degrees for the supercardioid and 105 degrees for the hypercardioid – alongside greater rejection of ambient sound. Additionally, while the cardioid is least sensitive at the rear (180 degrees off-axis), the supercardioid is least sensitive at 125 degrees and the hypercardioid at 110 degrees. When placed properly they can provide more 'focused' pickup than the cardioid pattern, but they also have less rejection at the rear. If you're using either of these polar patterns on stage with wedge monitors, it's important make sure you avoid placing the wedges directly behind the mic in this instance. Instead, place them either side at the mics least sensitive angle.

How many open microphones can I use before feedback becomes a problem?

Every time you double the number of open microphones, you lose about 3 dB of gain before feedback. Use as few open mics as possible, and mute or gate unused ones.
See Feedback / Microphone#Open Microphones.

How should I use EQ to reduce feedback?

Use EQ sparingly. Avoid excessive high‑frequency boost, and use ParaEQ to notch out a single problem frequency if needed.
For step‑by‑step notching instructions, see Feedback / Microphone#Notch Out a Problem Frequency.

Do vocal effects increase feedback?

Yes. Turn off effects until you have stable gain, then add them back one at a time so you can hear their impact.
See Feedback / Microphone#Effects.

Do instrument pickups help reduce feedback?

Yes. Pickups provide much higher gain‑before‑feedback than microphones and avoid the distance/position issues of miking an instrument.
See Feedback / Microphone#Instrument Pickups.

Sub1/Sub2

Sub1 Sub2

Sub1/Sub2‎‎

Sub Comparison

S1 Pro with Sub1 or Sub2

Bose App / Music App / L1 Mix App

As of 2025 The current app for Bose Portable PA is the Bose App.

This applies to all L1 Pro and the S1 Pro+

Get it on the Google Play Store or the Apple App Store.

ToneMatch Mixers

T4S

T8S

Engineered with a powerful DSP engine and intuitive user control, the T4S/T8S ToneMatch mixers offer studio-quality EQ, dynamics and effects. Sound great with integrated BoseToneMatch processing and zEQ, especially when connected to a Bose L1 or F1 system for full end-to-end tonal control.

read more — T4S/T8S ToneMatch® Mixers

Other Bose Portable PA Products

L1 Legacy F1 S1 Pro

[TM_Mixer-1] T4S ToneMatch mixer or T8S ToneMatch mixer or T1 ToneMatch Audio Engine

[2] Microphone Techniques - Shure Notes

[1]

[2]

@@ Line 4: / Line 4: @@
      <div>__TOC__
-The L1 Pro models share a common user interface and the L1 Mix app. This page has links to resources for all three models and the Bose products that integrate with them.
+The L1 Pro models share a common user interface and the L1 App. This page has links to resources for all three models and the Bose products that integrate with them.
+If you have an L1 Pro, check out the [[L1 Pro FAQ|L1 Pro Frequently Asked Questions]]
 </div>
 <div>
@@ Line 10: / Line 12: @@
 == L1 Pro Family ==
-Bose Pro announced the Bose L1 Pro line, October 26, 2020.
+Bose Pro announced the Bose L1 Pro line on October 26, 2020.
@@ Line 31: / Line 33: @@
 [[File:ToneMatch_Mixers_Family_Ortho_Top_halfRes.jpg|link=T4S/T8S ToneMatch® Mixer|200px|class=hero|Learn about the T4S/T8S ToneMatch mixer]]
+If you have an L1 Pro, check out the [[#FAQ|L1 Pro Frequently Asked Questions]]
@@ Line 57: / Line 61: @@
 [https://www.youtube.com/watch?v=GZGRwhRXRNc L1 Pro and the Mobile DJ - video]
+<!--
 [https://community.bose.com/t5/Portable-PA/bd-p/PortablePA Bose Pro Portable PA Community]
+-->
 [https://proedu.bose.com/pages/60/l1-pro-series-certification-course L1 Pro Technical Certification Course] (no charge, but you must register)
@@ Line 122: / Line 126: @@
 ==== L1 Pro Line Out ====
 {{L1 Pro Line Out}}
+==== L1 Pro ToneMatch Switch ====
+;The ToneMatch switch selects the ToneMatch Preset applied to the input.
+It does not adjust the channel’s gain staging or level. It does not function like a MIC/LINE switch found on some powered loudspeakers or mixers
+{{ToneMatch Switch}}
 ==== L1 Pro Daisy Chain ====
@@ Line 134: / Line 143: @@
 </div>
-=== FAQ ===
+==== L1 Pro Emergency Kit ====
-;Q: What are the mid-high array and lower mid-high array made from?  Metal mesh front and is rear metal or plastic?
+{{:L1 Pro Emergency Kit}}
-;A: Arrays on all units feature an extruded aluminum sleeve. Perforated grille on the front, solid on the back. Source: [https://www.facebook.com/groups/BoseL1/posts/10161224768097446?comment_id=10161256043032446 Craig Small]
-;Q: Are the column speaker arrays interchangeable between the different models? (L1 Pro8, L1 Pro16, L1 Pro32)
-;A: No. While the column arrays and extensions of the L1 Pro8 and L1 Pro16 will fit each other, no sound comes out.
+== FAQ ==
+{{L1 Pro FAQ}}
 == Sub1/Sub2 ==
@@ Line 151: / Line 157: @@
 [[S1 Pro with Sub1 or Sub2]]
-== Bose Music App / L1 Mix App ==
+== Bose App / Music App / L1 Mix App ==
-{{Bose Music App}}
+{{:Bose App}}
 == ToneMatch Mixers ==

Difference between revisions of "Template:L1 Pro"

Latest revision as of 12:46, 23 February 2026

Contents

L1 Pro Family

Documentation

L1 Pro8

L1 Pro16

L1 Pro32

Sub1/Sub2

L1 Pro Technical Data Sheets

L1 Pro Service Manuals

L1 Pro Self-Serve Support

Application Guide

L1 Pro Firmware

Resources

Articles

Comparing Specifications

Comparing L1 Pro Models

Legacy to L1 Pro Models

Quick Tips

L1 Pro Line Out

L1 Pro ToneMatch Switch

L1 Pro Daisy Chain

L1 Pro System EQ

L1 Pro32 Half Stack

L1 Pro Emergency Kit

FAQ

General Questions

Inputs and Connections

Multiple L1 Pro Systems

Troubleshooting

Feedback Issues

Set Up Your Source

Trim Controls

Omnidirectional and Unidirectional Microphones

Omnidirectional Microphone

Unidirectional Microphone

Cardioid

Supercardioid / Hypercardioid

Sub1/Sub2

Bose App / Music App / L1 Mix App

ToneMatch Mixers

Other Bose Portable PA Products

Navigation menu

Search