S1 Pro system

From Bose Portable PA Encyclopedia
Revision as of 11:32, 10 July 2019 by ST (talk | contribs)
Jump to: navigation, search

S1 Pro  This information is applicable to the S1 Pro system
This Page Reviewed By Bose

Contents

S1 Pro Tilt.jpg

Introduced January 23, 2018

Discuss it here: S1 Pro System Community

Documentation

S1 Pro system Owners Guide

S1 Pro Service Manual


Downloads

S1 Pro System Firmware updates & Bose Connect App

Product Images

Mechanical Files


Firmware

See: S1 Pro System Updates Version 7.0.10 June 2018

Related Products

Bose S1 Pro Compared to Bose L1® Compact

S1 Pro Introduction

Unboxing and Setup

Input/Output Panel

Overview

S1 Pro Connections and Controls.jpg

Gain Staging

Using a Bose device as the source

When connecting a ToneMatch Mixer[1] or an S1 Pro System Line Out to an S1 Pro System channel 1 or channel 2

Set the volume control to 10:00 o'clock with 1/4 inch (6.3 mm) Tip-Ring-Sleeve

The signal strength from a ToneMatch Mixer[1] or an S1 Pro System Line Out is sufficient to achieve the maximum usable volume from the S1 Pro System
Control the overall volume from the ToneMatch Mixer[1] or the first S1 Pro System. If you use an XLR cable, set the volume control to 9:00 o'clock

ToneMatch Mixer to S1 Pro.jpg


Using a third-party source (not a Bose device as the source)

For each channel you are using on the S1 Pro System

  1. Turn the channel volume off
  2. Connect your sound source
  3. Adjust the volume of the source device output to the reference or nominal output level.
    • On analog consoles this may be marked as unity or 0 dB.
    • On digital consoles this may be marked as -18 dBFS[2][3]. The exact value (-18 dBFS to -20 dBFS) may vary depending your location[4].
    • Refer to the manual for the source device for details.
    • If the source device does not have metering or indicators, set the output as high as you can without hearing distortion or seeing red indicator lights.
  4. While playing/singing as loud as you will during your performance, bring up the channel volume until you see solid green on the channel indicator light. Occasional flickers of red are okay. If you see solid red or you hear distortion, turn down the volume.

Input Gain

S1 Pro IO Panel 1024.jpg
Channels 1 and 2
  • XLR: -infinity to + 49 dB
  • 1/4 inch (6.3 mm) Balanced input (Tip-Ring-Sleeve): -infinity + 42 dB
  • 1/4 inch (6.3 mm) Unbalanced input (Tip-Sleeve): -infinity + 36 dB
Aux
  • 1/8 inch (3.1 mm) Sterero (Tip-Ring-Sleeve): -infinity to + 17 dB
Recommended Connections

Related: Balanced vs Unbalanced

Further Reading


Tone Controls

Channels 1 and 2

  • Bass +/-8 dB @ 100 Hz (60 Hz – 900 Hz)
  • Treble +/-10 dB @ 10 kHz (1.5 kHz – 17.4 kHz)

Aux Input

When you insert a 1/8" (3.5 mm) jack in the Aux input, this disables streaming Bluetooth.

S1 Pro Aux Input.jpg

Microphone vs Guitar Volume

Different Volume Control Levels

Question
Why do I have to turn up the microphone higher than guitar?
Answer
The output level of the guitar is louder than the output level of the microphone. That's why we have to turn up the microphone higher.

S1 Pro Mic higher than Guitar

In the picture above the

  1. Microphone is connected to channel 1
  2. Guitar is connected to channel 2

The volume on channel 1 (microphone) is higher than on channel 2 (guitar) because the signal from the microphone is lower than from the guitar.

Background Information

  • The power amps are running at full volume
  • The volume controls are trim controls:
  • Note how quiet the S1 Pro is when there’s no input source and the volume, is all the way up – The volume controls are trim not preamp/gain controls
  • The center detent is a convenient point of reference, especially when you can't see the controls well at a gig
    It is not an indication of a specific amount of gain
  • When you turn the volume controls all the way up, you have reached the maximum volume the S1 Pro is capable of producing for that source
  • Note the clip lights. If you see red, turn down to avoid distortion. You have reached the maximum usable volume just below clipping

The maximum usable volume for an input is just before the clip lights come on. With a guitar with a preamp, that might be at 12:00 o’clock compared to a microphone at 3:00-4:00 o’clock.  There’s no dysfunction here. It’s a reflection that the output level of the guitar is higher than the microphone.

We want you to enjoy your S1 Pro system without having to be concerned about the inner workings. Just plug in your microphone and instrument, turn up the volume and perform.

Please use the volume controls to get the loudness you need for your show. It's not necessary to have the volume controls at the same level. And unless you have similar input sources it's unlikely the controls will be at the same level.

Maximum Usable Volume

When the channel is clipping (red light), or you hear audible distortion, you have reached the maximum usable volume the S1 Pro can provide. This can happen lower or higher on the volume control depending on the signal strength of your source.

Unless you have an input source that is lower than a typical microphone or guitar with a passive pickup, you should not need to add another device between your source and the S1 Pro. You can add preamps, processors, pedals, or transformers if you like, but it's unlikely that any of these will change the maximum volume the S1 Pro system can provide.

Volume below and above 12:00 o'clock on volume controls

There is no special processing or split in the way we handle the signals below and above 12:00 o'clock on the volume control.

What you are experiencing is directly related to the input signal. If you have a very low input signal (e.g., microphone or bare piezo pickup), you will need to turn up volume control to hear that signal, compared to a higher input signal (e.g., microphone through a mixer or wireless receiver or a guitar with a built-in preamp).

If you connect a microphone or a guitar to a ToneMatch (or other) mixer, turn the output volume down, connect it to the S1 Pro through a 1/4 inch input, you can get the same behavior as connecting a microphone to the XLR input - very little response until you turn up the volume. The point at which you hear sound will be directly related to the output volume on the mixer. That point is may not be 12:00 o'clock. It will depend on the output of the mixer.

Suggestions

If you've got the microphone channel volume all the way up, you may be able to get a bit more by turning up the bass and treble.

When the channel LED light goes solid red, you have reached the maximum volume available for the channel. Adding a mixer between the microphone and the S1 Pro will not give you a louder, cleaner signal if it is already solid red. All you'll get is distortion.

If you have a microphone with relatively low sensitivity (e.g., Shure SM58), consider getting a microphone with a higher sensitivity. See Dynamic Microphones for a list.

Make sure you have the ToneMatch Preset switch set to MIC for the microphone and GUITAR for the guitar.

If you've maxed out your options with the microphone channel, try turning down the guitar to get a better mix.

Impedance Matching Transformer

There's nothing gained by using an impedance matching transformer. To match the performance you get with the impedance matching transformer, without one, turn up the volume control. Either way, you have reached maximum usable volume when the input clips and you hear distortion. You may get to that point at a lower setting on the volume control with the impedance matching transformer, but with or without it, the maximum output available is the same.

You may feel better if the volume controls are closer to the same setting (using an impedance matching transformer) however, this adds another device to your signal chain. It's another potential point of failure, and a relatively large device to plug directly into the S1 Pro. You don't want to damage the input if you knock over the S1 Pro and it hits the impedance matching transformer.

Wireless Microphone Receiver

Some wireless microphone receivers have output level controls or different outputs with different signal levels.

If there is a line-level output and you use that, then the signal level will be higher than a wired microphone. You will reach the maximum usable volume at a lower setting on the volume control.


Related conversation: S1 Pro Volume Controls - Why do I have to turn up the microphone higher than the guitar?


ToneMatch® Presets

On Channels 1 and 2 you can select a ToneMatch® Preset.

S1 Pro ToneMatch Switch.jpg

These are the equivalent Presets on the ToneMatch® mixers (T1, T4S, T8S)

Off

Category: Utility
Preset: Flat

L1 Compact equivalent: Channel 2, Line Level (switch position down)

Guitar

Category: Acoustic Guitars
Preset: Steel String w/piezo

L1 Compact equivalent: Channel 2, Guitar (switch position up)

Microphone

Category: Vocal Mics
Preset: Handheld Mics

L1 Compact equivalent: Channel 1

The Microphone Preset includes a sharp low-cut filter, keeping only that part of the audio spectrum where the microphone is useful. Using the microphone with this preset minimizes bass regeneration. The microphone preset was developed for close microphone use (“eat the mic”), which is the best way to optimize your vocal signal for tone and gain before feedback[5].
About the presets: No mic that I know of sounds good for close vocal, even for recording for that matter. All our presets compensate for this. A lot of these mics sound a lot more natural when you back off a foot or so from them. Of course, this is true in the studio too. No one does this for a live performance (backs very far off the mic) since you want to maximize gain before feedback by eating the mic. And so then you get funny sound and so then you need our presets to make it natural. [6]

Power Switch

S1 Pro Power Closeup.jpg
In Use
Set the power switch to the top position (on).
Standby/Off
When you are not using the S1 Pro System you can leave the power switch in the standby position (middle) or the quick-charge position (bottom).
If the S1 Pro System is not connected to AC power, it won't matter if you choose the middle or bottom position.
In Transit
You can put the S1 Pro System power switch in the bottom position (quick charge) position when transporting the unit. This may reduce the likelihood the switch will get bumped to the on position.
Charging
When you are charging the S1 Pro System you can put the power switch in the standby position (middle) or the quick-charge position (bottom).

More detail.

S1 Pro Power.jpg


S1 Pro LEDs

Introduction

There are two power related LEDs: Power on the front of the system and Battery Status on the back of the system next to the power switch.

There are three LEDs for signal input.

There is one LED for Bluetooth.


Summary
There are two power-related LEDs: Power on the front of the system and Battery Status on the back of the system next to the power switch.
There are three LEDs for signal input.
There is one LED for Bluetooth.

S1 LED status

S1 Pro LEDs 1.jpg

Power LED


Power LED on the front of the unit
Off System is off
Blue System is on
Blue (flashing) System is in low power sleep mode
Happens after dormant for an hour
Resumes automatically when an audio signal is present
Red System fault

 

Power/Battery LED

S1 Pro LEDs 2.jpg

If using the battery the LED next to the system power switch shows the battery's charge state by flashing when powered on. To check the charge at any time, double-press the Bluetooth button in the Input 3 section.
 

Blue - 4 flashes 75 - 100% charge
Blue - 3 flashes 50 - 74% charge
Blue - 2 flashes 25 - 49% charge
Blue - 1 flash - may appear to be flashing 10 - 24% charge
Red - 1 flash Less than 10% charge

Signal LED

There are 3 signal LEDs: one above the volume knob for Inputs 1, 2 and 3.


 

Off No or low level signal present
Green Signal present
Red Signal clipping


Bluetooth LED

The Bluetooth LED is located on the Bluetooth button under Input 3 on the connection / control panel.


 

Off Bluetooth is off
White (flashing) Pairing mode / connecting
White (solid) Connected to Bluetooth device

 




Battery

Documentation

S1 Pro Battery Owners Guide

Run Time

Up to 11 hours of play .

The full output of the S1 Pro system is available even when running on the internal battery. This is unlike some systems that throttle performance to extend the battery life.

Your run time will vary based on:

  • Volume and to a lesser extent the tone controls
Higher volume and turning up the tone controls draws more energy than lower settings.
  • Program material
Prerecorded music is usually compressed. This may draw more power than live music at the same perceived volume because live music has more dynamics (lower draw in quiet moments).

Charging Times

S1 Pro Standby

Estimates:

  • 6.0 hours Trickle charge (system idle, connected to AC Power), switch in Standby or Play position
  • 2.5 hours Fast charge (connected to AC Power), switch in Fast Charge (down) position


Checking the Battery Level

To check the battery, turn on the S1 Pro (switch in the top position). Wait until the power light is steady blue. Double tap the Bluetooth button (tap tap in under a second). Count how many times the power light blinks before returning to steady blue.

NOTE If you are running your S1 Pro System and battery LED turns solid red - the battery is nearly out of power. Connect to AC power to keep the show going.

S1 Pro Battery Charging.jpg


Battery Specifications

S1 Pro Battery Label

Battery Life

The S1 Pro uses a lithium-ion battery. Individual battery performance will vary due to battery age, storage conditions, and the number of charge cycles.

S1 Pro Standby

Bose does not guarantee how long a lithium-ion battery will retain its charge. However, we expect a fully charged battery in a new S1 Pro system will last 30 days with the power switch in the “Standby” () position if the system is using Firmware 7.1.5[7] or later.

After 30 days of non-use, the battery will enter Sleep Mode. Bose recommends that you wake up[8] the battery and fully charge it at least once a year. If you leave it in Sleep Mode for longer than a year, the battery may completely discharge and become unusable.

Additional reading Battery Life.


Temperature Considerations

Please note the following information from the S1 Pro Battery Pack Owner’s Guide:

  • Charging temperature range: 0°C - 42°C (32°F - 108°F)
  • Discharging temperature range: -20°C - 45°C (-4°F - 113°F)

You can operate the S1 Pro on the battery pack down to -20°C (-4°F), The running time may be reduced but not significantly.

NOTE
The battery does not charge temperatures below 0°C (32°F).


The battery will stop charging when the temperature is below 0°C - 42°C (32°F - 108°F) but the charging light may continue to flash.

The battery will stop functioning below -20°C - 45°C (-4°F - 113°F)


If you have questions on this point please see Battery Life in the Cold

Installation and Removal

S1 Pro Battery Installation.jpg


The screw heads are Phillips.

S1 Pro Phillips.jpg Philips head screwdriver Horz.jpg

Note: The screws remain attached to the battery cover. You can't misplace or lose them because they don't separate from the battery cover.


Sleep Mode

Here is an excerpt from the S1 Pro Battery Owners Guide

S1 Pro Battery Sleep Mode.jpg


Sleep mode is to protect the battery.

Sleep mode is the lowest current draw of the integrated circuits (ICs) in the battery pack. If the ICs were left unchecked, eventually they would drain the cells below their safety threshold. When the cells are allowed to discharge below a certain level, they become susceptible to dendritic growths within the cells. This can lead to catastrophic failures of the cells. The battery fails and is non-recoverable.

We use the sleep mode (or shipping mode) to extend the timeline long enough to greatly reduce the occurrence of failed battery packs.

If you have lithium-ion battery powered tools, you have probably experienced this. You put the tool away at the end of the season. Next year, you take them out again to use them only to find the battery no longer works and you have to replace it (you prevent this by storing them in the charger instead of leaving it in the tool). The use-profile for the S1 Pro System is that it will be used in the warmer months, and with a very high likelihood, it will be put away in the colder months. This is why we put it back into sleep mode when not in use for more than 30 days.


Flying with the Lithium Ion Battery

Here's some information about Flying with Lithium Ion batteries from the FAA

https://www.faa.gov/about/init.../more_info/?hazmat=7

Size limits: Lithium metal (non-rechargeable) batteries are limited to 2 grams of lithium per battery. Lithium ion (rechargeable) batteries are limited to a rating of 100 watt hours (Wh) per battery. These limits allow for nearly all types of lithium batteries used by the average person in their electronic devices. With airline approval, passengers may also carry up to two spare larger lithium ion batteries (101-160 watt hours). This size covers the larger after-market extended-life laptop computer batteries and some larger batteries used in professional audio/visual equipment.

The battery in the S1 Pro is rated at 79.20 Wh. That's not in the documentation, but it is on the label on the battery.


Pole Cup Switch

The S1 Pro uses an accelerometer to determine if it is in the tilt-back, horizontal or vertical position. It also has a switch inside the pole cup to determine if it is mounted on a speaker stand. Based on the orientation and the switch, the S1 Pro automatically applies the correct EQ. If you depress the switch the speaker stand EQ is applied regardless of the orientation of the S1 Pro.

Here's a picture of the switch inside the pole cup.

S1 Pole Cup 1.png

S1 Pole Cup 2.png

Warning - Do NOT use Speaker Stands Like This

Ultimate Support TS30.png

Bose recommends using speaker stands that have solid, smooth surfaces. Do not use stands like the one shown below. It will damage the switch in the pole cup.

Warning - Do NOT use speaker pole adapters

Bose recommends that you do NOT use speaker stand adapters like the Hercules SS100B. You could damage switch in the pole cup.

Hercules SS100B Adapter.jpg

Channel 3 Volume Control

The S1 Pro System channel 3 volume control behaves differently than the volume controls on channels 1 and 2.

Slow to Respond

If you find the volume control seems slow to respond (especially between 7-11 o'clock) please turn up the volume at the source (Bluetooth or physical connection).

For Bluetooth connections, if you set the volume on the source device to maximum, this will give you the greatest usable range on the S1 Pro Aux Channel volume control.

S1 Pro Channel 3

Steps in Volume

The S1 Pro has a digital gain knob on channel 3 which is divided into incremental steps. When you slowly turn the volume knob up with a strong input signal present, you may hear steps in loudness.

We are aware of this behavior and it is not a symptom of a fault or malfunction.

Volume Cut Off

This affects the sound connected to the Aux input and Bluetooth streaming.

S1 Pro Channel 3 Volume.jpg

The sound stops at about 8:00 o'clock although it appears that should happen at 7:00 o'clock on the dial. The transition to silence

  • will be smoother when the source signal is low
  • will be more abrupt when the source signal is high

This is normal for this control.

The control is digital (functioning in steps). With a low signal source, the change you hear for each step will be small. With a high signal source, the change you hear for each step will be larger.


Noisy Volume Controls

On S1 Pro system channels 1 and 2: When you rotate the volume controls back and forth within 10 seconds of turning on the unit, you may hear a scratchy sound.

This is not a symptom of a hardware issue with the volume controls that warrants concern.

The noise is related to a start-up process within the unit, not the volume controls. The noise you hear is not the result of a physical problem with the volume controls.

When you turn on the unit and rapidly turn one of the volume controls back and forth you may hear a noise. This can happen on either channel, 1 or 2.

After several seconds, the sound stops. At this point, the volume controls on both channels 1 and 2 should work as expected, quietly.

If you cycle the power off and back on, you can get the same result on the other channel, 1 or 2.

If you turn on the unit and let it sit for 20 seconds, the volume controls are quiet. That doesn't mean you have to wait for 20 seconds before you can use the unit. You just have to wait for 20 seconds if you don't want to hear the noise when you rotate the volume controls quickly.

Related discussion in the Bose Portable PA Community

Orientations and Dispersion

Dispersion

In the speaker stand, tabletop, and tilt-back orientations

  • Horizontal 120 degrees
  • Vertical 50 degress

In the Horizontal (monitor) orientation

  • Horizontal 50 degrees
  • Vertical 120 Degrees

Auto EQ

If you take a loudspeaker and put it on a speaker stand, then a table top, and then on the floor, the sound will change*. When the speaker is on a table top or the floor, it is interacting with the boundaries (table top, floor, walls and ceiling too). This means, if you want great sound in all situations you have to EQ the loudspeaker.

Bose tuned the S1 Pro to sound great in all four positions (speaker stand, table top, floor (both tilt-back and horizontal)) taking into account the boundaries. And the engineers carefully considered how you would be using the S1 Pro . That's why there are two settings for the floor (tilt-back and monitor).

I encourage you not to second-guess the automatic EQ. To use them in ways other than Bose intended you'd have to put the loudspeaker in a free field (a room without reflections).

But if you could put the S1 Pro in a free field here's what might hear.

⇒ Using the speaker stand position as a reference (basically, flat):

⇒ Table top: a little less bass than speaker stand

Auto EQ Table.png

⇒ Tilt-back: a little less bass than Table top.

Auto EQ Tilt Back.png

⇒ Horizontal: about the same as Tilt-back except there's some EQ treatment to support use as a monitor.

Auto EQ Floor Monitor.png

Line Out

Overview and Specifications

The S1 Pro System Line Out is
¼ inch (6.3 mm) Tip-Ring-Sleeve jack: Nominal +2.4 dBu, Max +20 dBu
Output Impedance: 9.4 kilo-ohm kΩ
The Line Out is not affected by the Auto EQ. It's the combined output of all three channels (with volume controls, ToneMatch Presets, tone controls, and reverb) and is same whether the unit is in tilt-back, monitor, tabletop or on a speaker stand.
Notes
  • Using a Tip-Sleeve unbalanced cable will result in a drop in the audio level of -6dBu.
  • There is no limiter on this output so you may get more than the rated maximum, but it could sound distorted.

S1 Pro Daisy Chain (one to another)

S1 Pro Daisy Chain Settings This is an overview of how to connect one S1 Pro System to another.

  1. On the first S1 Pro turn off the volumes of all channels
  2. Run the LINE OUT to the second S1 Pro system using a balanced cable (1/4 inch (6.3 mm) Tip-Ring-Sleeve cable
  3. On the second S1 Pro set the volume to 10:00 o'clock. This should give you the same volume on the second unit as the first
  4. On the first S1 Pro bring up the volume to the appropriate level on the channels you are using

S1 Pro Daisy Chain.jpg

There is no reason to turn the second S1 Pro system above 10:00 o'clock because it will be louder than the first system and the signal will clip and distort before the first system does.


On the second S1 Pro System, for each channel you are connecting to the first S1 Pro System use these settings while you are setting up.

S1 Pro Settings for mixer.jpg

  • Reverb OFF
  • Bass at 12:00 o'clock
  • Treble at 12:00 o'clock
  • ToneMatch switch OFF

You can adjust the Reverb, Bass, and Treble after you get your basic sound working.

S1 Pro+

You can also connect to the Channel 3 Aux input. For best results, use a 1/4 inch (6.3 mm) Tip-Ring-Sleeve cable.

S1 Pro+ Channel 3 Inputs.jpg



Gain Staging

Using a Bose device as the source

When connecting a ToneMatch Mixer[1] or an S1 Pro System Line Out to an S1 Pro System channel 1 or channel 2

Set the volume control to 10:00 o'clock with 1/4 inch (6.3 mm) Tip-Ring-Sleeve

The signal strength from a ToneMatch Mixer[1] or an S1 Pro System Line Out is sufficient to achieve the maximum usable volume from the S1 Pro System
Control the overall volume from the ToneMatch Mixer[1] or the first S1 Pro System. If you use an XLR cable, set the volume control to 9:00 o'clock

ToneMatch Mixer to S1 Pro.jpg


Using a third-party source (not a Bose device as the source)

For each channel you are using on the S1 Pro System

  1. Turn the channel volume off
  2. Connect your sound source
  3. Adjust the volume of the source device output to the reference or nominal output level.
    • On analog consoles this may be marked as unity or 0 dB.
    • On digital consoles this may be marked as -18 dBFS[9][10]. The exact value (-18 dBFS to -20 dBFS) may vary depending your location[11].
    • Refer to the manual for the source device for details.
    • If the source device does not have metering or indicators, set the output as high as you can without hearing distortion or seeing red indicator lights.
  4. While playing/singing as loud as you will during your performance, bring up the channel volume until you see solid green on the channel indicator light. Occasional flickers of red are okay. If you see solid red or you hear distortion, turn down the volume.

Combo Inputs

S1 Pro Channels 1 and 2 have combo inputs that accept
  • XLR (balanced mono)
    • Microphone or Line-Level inputs
  • 1/4 inch (6.3 mm) Tip-Ring-Sleeve connection (balanced mono)
    • Line-Level inputs
  • 1/4 inch (6.3 mm) Tip-Sleeve connection (unbalanced mono)
    • Line-Level inputs and instruments (e.g. guitars, keyboards, guitar processors, loopers)
When using a third-party device (e.g., mixer or another line-level source) should I use the XLR or 1/4 inch inputs?
  • The S1 Pro 1/4 inch Tip-Ring-Sleeve inputs are best suited for line-level balanced inputs. This is a better match for the signal level.
  • The S1 Pro XLR inputs are best suited for microphones.

When the S1 Pro Channel input lights hit red or you hear distortion, the signal is clipping and you've reached the maximum usable volume. From the source, if the XLR outputs are line-level and the 1/4 inch Tip-Ring-Sleeve outputs are line-level, it won't matter which type of cable you use. They'll both get the job done, although the volume control setting will be lower with the XLR connection. That doesn't indicate more headroom. The maximum usable volume is the same either way.




Alternate Connection

You can use an XLR cable (mic cable) from a Line Level Source (e.g., L1 Pro, S1 Pro+) to second S1 Pro System channels 1 or 2 (XLR inputs), but the signal may clip, overload, or be too high to control the volume. To attenuate (reduce) the signal, use a -20 dB or -30 dB Pad

XLR Cable

XLR cable.jpg

Pad

More about Pads

Click image for more information about Pads

Connecting a Mixer to an S1 Pro system

Article from Bose Connecting an S1 Pro to a mixer



Connecting the S1 Pro System to a Third Party Device

S1 Pro to a Third Party Device


Bluetooth

Version

The S1 Pro system supports Bluetooth version 4.2

Bluetooth Light

  • Fast blink - attempting to re-connect with previously paired devices
  • Slow blink - in pairing mode
  • Solid - connected

Bluetooth Pairing

  1. Turn on the Bluetooth feature on your mobile device.
    Note: The Bluetooth feature is usually found in the Settings menu.
  2. Press and hold the Bluetooth Pair button for two seconds.
    Note: When ready to pair, the Bluetooth button will flash white.
  3. Select your Bose® SI Pro system from the device list.

Note: When the device pairs successfully, the Bluetooth button will turn solid white. Note: If your paired phone receives a call, any music playing will be paused and the ring will come through the phone: no calls or notifications will come through the SI Pro.

Once you have paired the S1 Pro system to a Bluetooth device, the S1 Pro system will automatically connect to that device when you turn on the S1 Pro system if it is powered on and within range. If you want to terminate that connection, terminate the connection on the Bluetooth device.

More detail on Bose.com

Clear the Bluetooth Pairing List

  1. Press and hold the Bluetooth button. until it goes dark (about 7-10 seconds).
  2. On your Bluetooth device, remove the Bose S1 Pro from the device list.

You are now ready to pair the S1 Pro to a Bluetooth device.

Turn off Bluetooth

You cannot turn off Bluetooth however, Bluetooth will turn off after about two minutes after you turn the power on unless the S1 Pro successfully connects to a Bluetooth device.

When you turn on the power on the S1 Pro, it will attempt to connect to a paired device via Bluetooth. If there are no paired device, it will go into pairing mode.

If the S1 Pro cannot connect to a paired device, the Bluetooth light will blink for about two minutes while it is attempting to connect. If it doesn't make a connection, the Bluetooth light will turn off (time out). At that point, the Bluetooth is off until the next time you turn the power off/on.

Disconnect a Bluetooth connection

If you have Bluetooth connection active and you want to disconnect it. If you manually disconnect, the S1 Pro system will time out after about 2 minutes, and Bluetooth will remain off until the next time you power off/on.

IOS

Starting with iOS 9, Apple has added a new option for Bluetooth devices:

  • Open Settings, select Bluetooth
  • Tap the "i" circle button to the right of the accessory.
  • From there, you can see the new "Disconnect" option, alongside the legacy "Forget This Device" choice.
Android

Disconnect or Unpair from a Bluetooth Device

  • From home, tap Apps > Settings > Connections tab > Bluetooth.
  • Tap the ON/OFF slider to turn Bluetooth on.
  • Tap the connected device, and then tap OK to disconnect.

Reconnect a Bluetooth Connection after a time out

If the S1 Pro system Bluetooth light is off (because it has timed out), if you press it briefly, it will blink.

With the Bluetooth light blinking, I've been able to initiate a Bluetooth connection from a previously paired device. This worked with:

  • An IOS 11.4 device
  • An Android 7.0 device
  • A Windows 10 device


Bass Content in Bluetooth

How can I reduce the bass in Bluetooth music
The S1 Pro System reproduces the audio received over Bluetooth. To change the EQ use an app in the Bluetooth source device.
See IOS Equalizer
See Bass over excursion... Community discussion
Will Bose issue a firmware update to change the bass response in Bluetooth content?
We tested the S1 Pro system with a wide range of applications including live music, music playback with various styles of music, public speaking, and more. We tuned the bass response for the best overall performance for the widest number of people. We continue to listen to customer comments here and through all channels. We know that most of our customers are extremely happy with the sound of the S1 Pro system.
We have explored ways to change the response in the low frequencies. We found making the S1 Pro system more tolerant of heavy bass diminishes the overall performance in other ways. We don't have plans to change the sound profile of the S1 Pro system through a firmware update. Source

S1 Pro System Bass Distortion with Bluetooth through Channel 3

There have been some discussions in the Bose Portable PA Community about bass distortion with Bluetooth sources through Channel 3. Will Bose issue a firmware update to fix this?
If you hear bass distortion you're hitting the maximum volume (bass) the S1 Pro system can handle. We tested the S1 Pro system with a wide range of applications including live music, music playback with various styles of music, public speaking, and more. We tuned the bass response for the best overall performance for the widest number of people. We continue to listen to customer comments here and through all channels. We know that most of our customers are extremely happy with the sound of the S1 Pro system.
If you need more overall volume for music playback you need a bigger enclosure. The L1 Compact and the larger L1 systems may be a better choice.


Source: S1 Pro Channel 3 has too much bass. Related discussion S1 Pro channel 3 bass over excursion

Consider using an app to control the sound at the source. For example Using the Spotify Equalizer with your S1 Pro system

We have explored ways to change the response in the low frequencies. We found making the S1 Pro system more tolerant of heavy bass diminishes the overall performance in other ways. We don't have plans to change the sound profile of the S1 Pro system through a firmware update.

S1 Pro with F1 Subwoofer

Can I use one or two S1 Pro Systems with an F1 Subwoofer?
Yes. Please see this discussion in the Bose Portable PA Community S1 Pros with F1 Subwoofer

Rotate the logo counter-clockwise NOT clockwise. Don't force it. You will break the mechanism.

Limiter

Does the S1 Pro System have limiters or internal protection?
Yes, the S1 Pro System has two separate limiters. One for the speaker array. One for the Woofer.

Note: If you hear distortion or the channel lights are red, turn down the volume.


S1 Pro System Reset

  1. Turn off the S1 Pro System
  2. Disconnect everything (audio, USB connections, Power)
  3. Remove the battery [12]
  4. Wait 30 seconds
  5. Reinstall the battery[12]
  6. Reconnect (audio, USB, Power)
  7. Turn on the power

FAQs

S1 Pro system FAQ

What makes the Bose S1 Pro multi-position PA system different from other PA systems?

The S1 Pro is the ultimate all-in-one PA, floor monitor, practice amplifier and primary music system. Multiple positions, supported by Auto EQ, ensure that you always sound your best. And with a 3-channel mixer, reverb, Bluetooth® streaming and ToneMatch processing onboard, the S1 Pro is ready to be your go-anywhere PA.

How do I set the system up?

1.) Choose your system orientation based on the application.
2.) Plug in the AC power cord or use optional battery
3.) Connect audio source. If using a guitar or microphone, set the ToneMatch switch to the appropriate setting.
4.) Turn the power on and turn up the volume controls.

What is the optimal placement when using the S1 Pro?

The versatile S1 Pro system operates in four unique modes and can be set up differently based on the application.
Elevated Surface
Position the S1 Pro on a surface. This projects sound clearly and evenly throughout the audience, and ensures that audience members enjoy the full frequency range of the system.
Tilt-Back
For performances where your audience is close to you, tilt the S1 Pro onto its back edge. For best results, the performer should stand or sit to one side of the loudspeaker to avoid blocking sound from the audience.
Monitor Mode
To use the S1 Pro as a personal floor monitor, place it on the ground horizontally, in front of and pointing toward the performer. Tilt the loudspeaker onto its side edge. Rotate the Bose logo counterclockwise to match your chosen mode.
Speaker Stand
Place one or two S1 Pro systems on speaker stands (sold separately) for general-purpose sound reinforcement.

What function does Auto EQ perform?

Auto EQ provides optimal performance by sensing the orientation of the S1 Pro multi-position PA system using internal sensors. Once placed into a new position, the system applies the optimal equalization curve to maximize the quality of sound.

Given its smaller size does the S1 Pro system project sound as far as the L1 Compact system?

The S1 Pro multi-position PA system produces horizontal coverage that is comparable to that of L1 systems. Longer line arrays, such as those found in these systems, can project sound further with less drop-off of sound levels than the smaller array found in the S1 Pro.

Is the S1 Pro multi-position PA system designed for Mobile DJ’s?

Yes. The enhanced portability, easy set-up and professional sound quality of the S1 Pro system makes it suitable for a variety of applications as a smaller PA system: DJs, community and athletic events, business presentations, or wherever high-performance and easy-to-use sound amplification is needed.

The S1 Pro features best-in-class Bluetooth® streaming with one-button pairing. A 3.5 mm input for connecting a DJ mixer, laptop, CD player, or portable audio device allows for wired operation. When making announcements, simply plug a dynamic handheld microphone into one of the microphone/instrument channels.

Two S1 Pro systems are recommended for DJ applications to help reproduce stereo sound. Additionally, a single S1 Pro system can be conveniently used as a satellite system for larger DJ events.

What are the benefits of the integrated ToneMatch processing?

Whether you’re using an acoustic guitar or a handheld dynamic microphone, ToneMatch allows you to match the sound of the source by maximizing the sonic properties through equalization.

How many channels does the S1 Pro system have?

Three. The S1 Pro system has two full-featured channels designed for live speech or musical performance and one channel dedicated to prerecorded material using Bluetooth® streaming or 1/8” (3.5 mm) source.

Does the S1 Pro multi-position PA system have an analog audio output for expansion?

Yes. The S1 Pro multi-position PA system has a balanced line output to send the master mix out to another S1 Pro or to an audio console. 

Are the S1 Pro systems compatible with T4S/T8S ToneMatch mixers?

Yes. However, please note that the optional ToneMatch power supply is required for operation. For musical performances that require access to our most advanced tone shaping library, a full suite of studio quality effects, dynamics processing, and expanded inputs and outputs, ToneMatch mixers are the recommended choice.
To use the T4S/T8S ToneMatch mixer with the S1 Pro multi-position PA system, connect a master output of the ToneMatch mixer to input 1 or 2 on the S1 Pro system. Adjust the master level of the ToneMatch mixer to at least 50% and adjust the S1 Pro input volume knob to the desired level.

How can I take advantage of instruments or devices that deliver stereo output?

A single S1 Pro multi-position PA system can combine the two channels and fill the venue with one speaker. For instruments or recorded material where stereo reproduction is essential, two S1 Pro systems can be used to deliver stereo sound.

How are you able to obtain such a high level of performance from a smaller system?

Great care was taken in the design process to ensure that all the speakers and electronics perform as one integrated system. This allows the S1 Pro multi-position PA system to be extremely efficient and maximize its acoustical output while maintaining its small profile.

Is the S1 Pro water resistant?

The S1 Pro is not water resistant. It does however ship with a slip cover for normal transport.

Can I connect an external subwoofer, such as the Bose B1 bass module, to the S1 Pro multi-position PA system?

No, the system does not support adding bass modules. However, the S1 Pro does provide a reasonable amount of bass from its integrated high-excursion woofer.

Where should the S1 Pro multi-position PA system be positioned on stage?

System placement requirements for the S1 Pro multi-position PA system are flexible. For optimal sound for both the audience and performer, position the system directly behind – or behind and slightly off to one side of – the performer.

Does the S1 Pro have a universal power supply, so it can be used with any wall outlet?

Yes. The S1 Pro has a universal power supply that allows it to operate in regions ranging from 100V – 240V. The proper power cord for the specific region in which the system was purchased is included in the product carton.

What is the warranty period on the S1 Pro multi-position PA system?

The S1 Pro multi-position PA system has a two-year limited warranty.

Can the S1 Pro multi-position PA system be used together with an L1 system?

Yes. All systems can share the same stage. The L1 Compact and L1 Model II systems have longer line arrays than the S1 Pro and can project sound further with less drop-off of sound levels than the smaller array found on the S1 Pro.

Where can I learn more about the S1 Pro multi-position PA system or L1 portable line array systems and obtain tips on maximizing the benefits of my system? Please visit the Bose Pro Portable PA Community

Source: Bose Pro



  1. 1.0 1.1 1.2 1.3 1.4 1.5 T4S ToneMatch mixer or T8S ToneMatch mixer or T1 ToneMatch Audio Engine
  2. dBFS
  3. dBU vs dBFS
  4. dBFS Analog Levels
  5. Original description of how the Microphone Presets work
  6. Cliff Henricksen talks about Microphone Presets
  7. Bose recommends that you update your firmware to the latest version for the best performance. See: S1 Pro Firmware Update for details.
  8. To wake up the battery from Sleep Mode, plug your S1 Pro into a power outlet and turn the power switch to the “On” () position. See: S1 Pro Battery Sleep Mode for details.
  9. dBFS
  10. dBU vs dBFS
  11. dBFS Analog Levels
  12. 12.0 12.1 Remove or Install the battery
    S1 Pro Battery Installation.jpg
    The screw heads are Phillips. S1 Pro Phillips.jpg Philips head screwdriver Horz.jpg Note: The screws remain attached to the battery cover. You can't misplace or lose them because they don't separate from the battery cover.